Seat Alhambra Key Problems
Seat's jumbo MPV family is among the top in its class when it comes to resales value. And with a brand new model on sale, it's better than ever.
There are many reasons why the key fob could not perform as it should, including a dead coin battery, damage to the receiver module, or signal interference. This article will walk you through the steps to make sure it works.
Water Damage
If your key fob for the seat alhambra survives the wash cycle or dip in the water or a pool, it's equipped with a waterproof chip. But, you shouldn't do this often because prolonged exposure to water can increase the chance of the key fob getting damaged. If your key fob stops functioning after exposure to rain or clean tap water, unplug the battery and clean the electronic component with a towel. Allow it to dry completely before replacing the battery. If you are exposed to soapy or salty water it is recommended to wash the chip using isopropyl alcohol or a electronic cleaner prior to trying to put the battery back in.
Faulty Receiver Module
If you have tried a new battery for a button and the key fob isn't locked or unlocking, it's likely that the receiver module has developed a fault. The positive side is that this is a fairly easy repair that is inexpensive, you can just disconnect the battery for just a few minutes (first take off the negative cable and press the horn button numerous times) to eliminate any remaining electric current, then reconnect it in reverse order e.g. Positive cable first and then negative.
ESP Warning Light If the ESP warning light flashes, it is normal and signifies that the car is driving over terrain where the traction between the road surface and the tyres isn't optimal, such as snow, gravel or lots of surface water. If seat car key replacement G28 is always on, it means that there is a problem in the system. This can be diagnosed with a iCarsoft i908 seat OBD code reader kit. It will give you an in-depth description of the fault.
Dead Coin Battery
A dead coin battery is one of the most common causes for the keys for the seat to cease to function. The key fob is powered by a small button-cell battery. It should be replaced with a brand new one that has exactly the same size, voltage, and specification as the original. If you're replacing your battery, be sure to remove all metal clips from the back of the key fob and make sure that the contacts are clean and free of corrosion.
If the key fob has been exposed water, like rain or soapy water it is recommended to remove the battery and clean the electronic chip with alcohol or an electronic cleaner prior to installing the new battery. The chip is sensitive to moisture and could be permanently damaged. If the key fob doesn't work after replacing the battery, it might be necessary to replace the key fob.
Faulty Receiver Module
If your key fob was not working after replacing the battery but it did not function, or suddenly stopped working the receiver module may have experienced a malfunction. The receiver module is able to receive radio frequency signals from the remote keyfob and converts them into electrical commands that are then followed by other modules inside the car.
If the receiver module has suffered a malfunction it will not respond to any of the commands transmitted by your remote key fob. In this situation you will require a dealer to reprogramme the key fob, and also install the new receiver.
The key fob comes with rubber seals that stop water from getting into the electronic chip inside. If you immerse your key fob into the ocean's salty or soapy water, the chip inside may be damaged. If your key fob does not work, you can try cleaning the chip with isopropyl or an electronic cleaner.
If the keys have been connected, but the receiver module is not working You can try to restart all the electronics that are on board by disconnecting the battery that is 12 volts for a few minutes. Then reconnect the battery in reverse order (negative cable first, then positive). This will reset the onboard electronic and restore their functionality.
Faulty Electronic Chip
The key fob comes with a tiny chip that transmits the signal from the key to the receiver module each time the key is used. If the signal isn't in line with the one the car has stored, the immobilizer will disable and stop the vehicle from starting. If, however, the key fob isn't working and you are not able to reprogram it then it could be due to a defective chip.
The chip in the key fob may have change in order to get it working again. This can be accomplished by getting the key fob removed from its case, and using a needle or pin to make contact with each metal retaining clip. If the clips are corroded, or damaged, you'll require replacement to allow the remote control to work. Make sure that the replacement batteries are of the same size, voltage, and specification as the original.
The Seat Alhambra is an attractive and well-designed model however, just like any other vehicle it is not without its challenges. problems with specific parts or equipment. For instance some owners have encountered issues with the auto climate control system, which can malfunction and cause problems in one particular setting. The infotainment system can also fail and cause freezing of the screens.